英文使用说明书-日本日置 CT6831/CT6830 AC/DC电流探头
文件名：英文使用说明书-日本日置 CT6831/CT6830 AC/DC电流探头
格式：PDF
大小：1.34 MB
页数：2页
本站仅提供预览学习使用，请勿用于商业用途
内容介绍
The device is classified as a Class A product under the EN 61326 standard. Use of the device in a residential setting may interfere with reception of radio and television broadcasts. If this occurs, take appropriate steps to counteract the issue.
Symbols on equipment
Indicates that the device can only be used at a location on an insulated wire with sufficient insulation for the circuit voltage.
Part Names
- PRESS button (open/close button)
- Current direction arrow
- Jaws
- DEMAG (demagnetization) button
- Option OADJ (zero adjustment) dial
- Output connector
- Serial number
- Relay box (rear)
The optional equipment listed below is available for the device. To purchase optional equipment, please contact your authorized Hioki distributor or reseller. Options are subject to change. Check Hioki's website for the latest information.
CT9902: Extension Cable (up to two cables can be connected together).
Phase Compensation Values
For phase compensation of the PW6001 or PW3390, enter the following compensation values (typical):
Frequency: 10kHz
- CT6830: -6.9°
- CT6831: -4.4°
The PW8001 automatically sets the phase compensation value, so it does not need to be entered manually.
Maintenance and Service
If the device malfunctions, contact your authorized Hioki distributor or reseller.
CAUTION: Observe the following when shipping the device:
- Remove optional equipment from the device.
- When requesting repair, include a description of the malfunction.
- Double-pack the device. Failure to do so could cause damage during shipment.
Cleaning
CAUTION: If the device becomes dirty, wipe it clean with a soft cloth moistened with water or a neutral detergent. Never use solvents such as benzene, alcohol, acetone, ether, ketone, thinners, or gasoline, and do not wipe with excessive force. Doing so could cause deformation or discoloration of the device.
Calibration
The appropriate schedule for calibration depends on factors such as the operating conditions and environment. Determine the appropriate calibration interval based on your operation.
Symbols on equipment
Indicates that the device can only be used at a location on an insulated wire with sufficient insulation for the circuit voltage.
Part Names
- PRESS button (open/close button)
- Current direction arrow
- Jaws
- DEMAG (demagnetization) button
- Option OADJ (zero adjustment) dial
- Output connector
- Serial number
- Relay box (rear)
The optional equipment listed below is available for the device. To purchase optional equipment, please contact your authorized Hioki distributor or reseller. Options are subject to change. Check Hioki's website for the latest information.
CT9902: Extension Cable (up to two cables can be connected together).
Phase Compensation Values
For phase compensation of the PW6001 or PW3390, enter the following compensation values (typical):
Frequency: 10kHz
- CT6830: -6.9°
- CT6831: -4.4°
The PW8001 automatically sets the phase compensation value, so it does not need to be entered manually.
Maintenance and Service
If the device malfunctions, contact your authorized Hioki distributor or reseller.
CAUTION: Observe the following when shipping the device:
- Remove optional equipment from the device.
- When requesting repair, include a description of the malfunction.
- Double-pack the device. Failure to do so could cause damage during shipment.
Cleaning
CAUTION: If the device becomes dirty, wipe it clean with a soft cloth moistened with water or a neutral detergent. Never use solvents such as benzene, alcohol, acetone, ether, ketone, thinners, or gasoline, and do not wipe with excessive force. Doing so could cause deformation or discoloration of the device.
Calibration
The appropriate schedule for calibration depends on factors such as the operating conditions and environment. Determine the appropriate calibration interval based on your operation.
预览图片
第1页
第2页